Shure A55M Shock Mount Microphone Clip Instruction Manual

1. Destpêk

The Shure A55M Shock Mount Microphone Clip is designed to significantly reduce the transmission of mechanical noise and vibration to your microphone. This accessory is crucial for maintaining clear audio quality in various recording and live sound environments by isolating the microphone from stand-borne disturbances. It is compatible with a range of Shure handheld microphones and other microphones with a 3/4 inch (25-30mm) barrel diameter.

Image 1.1: The Shure A55M Shock Mount Microphone Clip, shown in black. This device helps isolate microphones from mechanical vibrations.

2. Taybetmendiyên Hilberê

• Effective Vibration Reduction: Reduces mechanical noise and vibration transmission by over 20 decibels, ensuring cleaner audio capture.
• Pêveka Ewle: Provides a firm and stable connection for your microphone to a standard microphone stand.
• Lihevhatina Berfireh: Designed for handheld microphones with a 3/4 inch (25-30mm) barrel diameter.
• Avakirina Dorable: Made with robust materials for long-lasting performance.

3. Compatibility

The Shure A55M Shock Mount is compatible with handheld microphones that have a barrel diameter between 3/4 inch (25mm) and 30mm. This includes, but is not limited to, the following Shure models:

• Shure SM57
• Shure SM58
• Shure SM86
• Shure Beta57A
• Shure Beta58A
• Shure Beta87A
• Shure Beta87C
• Shure KSM109

Always verify your microphone's diameter to ensure proper fit and optimal performance.

4. Rêwerzên Sazkirinê

1. Li ser stûna mîkrofonê ve girêbide: Screw the Shure A55M Shock Mount onto a standard microphone stand or boom arm. Ensure it is tightened securely to prevent wobbling. The threads are brass for durability.
2. Mîkrofonê têxe: Gently slide your compatible handheld microphone into the rubber ring of the A55M shock mount. The rubber ring is designed to grip the microphone firmly.
3. Secure Microphone: Once the microphone is inserted, give it a couple of light twists to ensure it is properly seated and held securely within the rubber ring.
4. Angle Eyar bikin: If necessary, adjust the angle of the microphone by loosening the screw on the side of the shock mount with a flathead screwdriver, positioning the microphone, and then re-tightening the screw to maintain the desired angle.

Wêne 4.1: Berêample of the Shure A55M Shock Mount attached to a microphone stand with a microphone inserted, demonstrating typical setup.

5. Telîmatên Operating

The Shure A55M operates passively by isolating your microphone from physical vibrations transmitted through the microphone stand. No active controls or power are required.

• Positioning: Ensure the microphone is positioned correctly for your audio source. The shock mount allows for flexible positioning while maintaining isolation.
• Minimize External Vibrations: While the A55M significantly reduces vibrations, it is still advisable to minimize direct impacts or excessive movement of the microphone stand during use for optimal audio quality.
• Rêveberiya Cable: Route microphone cables in a way that does not pull on the microphone or stand, which could introduce unwanted noise or compromise the shock mount's effectiveness.

6. Maintenance

• Paqijî: Wipe the shock mount with a soft, dry cloth to remove dust or debris. Avoid using harsh chemicals or abrasive cleaners.
• Inspect Rubber Ring: Periodically check the rubber isolation ring for any signs of wear, cracking, or degradation. A damaged rubber ring may reduce the shock mount's effectiveness.
• Pişkên kontrol bikin: Ensure all screws, especially the angle adjustment screw, remain tight. Re-tighten gently with a flathead screwdriver if they become loose over time.
• Embarkirinî: Store the shock mount in a clean, dry environment when not in use to prolong its lifespan.

7. Destpêkirin

• Deng/Lerizîna Zêde:
  • Ensure the microphone is fully seated and secure in the rubber ring.
  • Verify the shock mount is tightly screwed onto the microphone stand.
  • Inspect the rubber ring for damage; replace the unit if the rubber is compromised.
  • Check if the microphone cable is causing tension or transmitting vibrations.
• Microphone Not Fitting Securely:
  • Confirm your microphone's barrel diameter is within the 3/4 inch (25-30mm) range.
  • Ensure the microphone is inserted straight and not at an angle that prevents proper seating.
• Angle Adjustment Loosens:
  • Use a flathead screwdriver to re-tighten the adjustment screw firmly. Avoid over-tightening.

8. Specifications

9. Garantî û Piştgirî

Specific warranty information for the Shure A55M Shock Mount Microphone Clip is typically provided with the product packaging or can be found on the official Shure website. For detailed warranty terms, product support, or service inquiries, please refer to the documentation included with your purchase or visit the official Shure support page.

Piştgiriya Serhêl: Visit Shure's Official Website