KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect
Specifications
- Product: STE-9000 series NetSensor
- Features: Temperature and humidity readings
- Model: All STE-9000 series NetSensors
Talîmatên Bikaranîna Product
- Ensure that both tabs on the sensor cover rest on top of the backplate.
- Make sure the anti-tamper hex screw is fully rotated into the backplate before installing or uninstalling the sensor cover.
- Swing the cover from the top onto the backplate.
- Do NOT push the cover directly onto the plate or swing it from the bottom.
- If any force seems to be needed, check the alignment of the tabs on the top of the backplate and/or the anti-tamper screw before swinging the sensor cover onto the backplate.
- For more detailed installation instructions, please refer to the STE-9000 Series NetSensors Installation Guide.
Pêngavên jêrîn biqedînin da ku NetSensorek dîjîtal a KMC Conquest STE-9000 Series siwar bikin û wê bi Kontrolkerek Conquest BAC-59xx/9xxx ve girêdin.
NOT: Binêre Conquest NetSensors STE- 9000 Series Digital Room Sensors pelgeya daneyan û Guide Hilbijartina Conquest at kmccontrols.com for specifications and other information.
NIVÎSK
- JI BO HERKIRINA CAMÛRÊN HESASTESA ELEKTROSTATÎK TÎDÎ BIGIHÎNIN
CÎHÊ ÇÎKIRINÊ HILBIJARTIN
- Binêre Rêbernameya Serlêdana Cih û Serîlêdanê ya Maintenance Sensor û Termostatê ya odeyê for cautions, troubleshooting, and best practices.
NOT: Berî ku senzorek saz bikin, li her cîhek têlkirina hişk temam bikin.
BACKPLATE RÊKIRIN
- Turn the hex screw(1) clockwise into the sensor until the screw clears the cover.
NOT: The hex screw(2_ should remain in the backplate.
- Qapaxê ji ser plakaya paş ve bikişînin.
CABLE ETHERNET GÊDÎ - Feed the Ethernet patch cable(3) from the Conquest controller through the center of the backplate(4).
NOT: Divê kabloya patchê ya Ethernet herî zêde 150 ling (45 metre) be.
- Bi karanîna pêlên peydakirî, paşîn li ser qutiyek elektrîkê bixin.
NOT: If additional thermal insulation is needed, install the optional HPO-9002 gasket before installing the backplate.
Ji bo bêtir agahdarî, binêre Room Sensor and Thermostat Mou
nting Location and Maintenance Application Guide. - Kabloya Ethernet-ê 5 têxin qulika modularî 6 ya sensor.
PÊKÊ HESORÊ SAS BIKE - Place the cover(7) over the top of the backplate(8) and swing it down.
NOT: Hişyar bin ku kabloya Ethernet neçin.
- Turn the hex screw(9) counterclockwise until it engages the cover.
BIKARANÎN
- The STE-9000 Series NetSensor becomes operational after it is connected to a powered Conquest controller.
- NOT: To change setpoints or configuration, see the KMC Conquest Kontrolker Rêbernameya Serlêdanê.
- NOT: For continued maximum NetSensor efficiency, see the maintenance section in the Rêbernameya Serlêdana Cih û Serîlêdanê ya Maintenance Sensor û Termostatê ya odeyê.
HIYARÊN GIRÎNG
- Materyalên di vê belgeyê de tenê ji bo armancên agahdariyê ye. Naverok û hilbera ku ew diyar dike bêyî agahdarî têne guhertin.
- KMC Controls, Inc. makes no representations orwarranties with respect to this document. In no event shall KMC Controls, Inc. be liable for any damages, direct, or indirect, arising out of or related to the use of this document.
- Logoya KMC marqeyek qeydkirî ya KMC Controls, Inc e. Hemû maf parastî ne.
TÊKELÎ
- TEL: 574.831.5250
- FAX: 574.831.5252
- e-mail: info@kmccontrols.com
FAQ
Q: Which models are affected by the installation issue?
A: This issue affects all STE 9000 series NetSensors.
Q: What are the potential errors from a damaged printed circuit board?
A: Incorrect temperature and humidity readings may result from a damaged printed circuit board.
Belge / Çavkanî
 |
KMC CONTROLS STE-9000 series NetSensor Damage from Incorrect Installation [pdf] Rehbera bikaranînê STE-9000 series NetSensor Damage from Incorrect Installation, STE-9000 series, NetSensor Damage from Incorrect Installation, NetSensor Damage from Incorrect Installation, NetSensor Damage, from Incorrect Installation |