SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Destpêk

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

Wêne 1.1: Pêşî view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Agahiyên Ewlekariyê

• Berî sazkirinê û xebitandinê hemî rêwerzan bi baldarî bixwînin.
• Pêbaweriya dabînkirina hêzê piştrast bikintage li gorî pêdiviyên cîhazê ye (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Amûrê di jîngehên ku zêde şilbûn, toz, an gazên korozîf tê de hene de nexebitînin.
• Disconnect power before performing any maintenance or wiring changes.
• Amûrê ji destwerdana elektromanyetîk a bihêz dûr bigirin.

3. Taybetmendiyên Hilberê

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Wide operating temperature range.
• Compact and easy-to-install design.

4. Naveroka pakêtê

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x Rêbernameya Bikarhêner (ev belge)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Sazkirin

5.1 Çêkirin

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Têlkirin

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Termînalên 1 û 2: AC Power Supply (85-265V AC, 50/60Hz)
• Termînalên 3 û 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Termînalên 6 û 7: Alarm Output (ALM) - Relay contacts for alarm.
• Termînalên 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Termînalên 11 û 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Telîmatên Operating

6.1 Nîşandana Serview

The meter features a dual display:

• PV (Nirxa Pêvajoyê): The upper red display shows the current measured temperature/humidity.
• SV (Nirxa Sazkirî): The lower green display shows the desired set point.
• Nîşana OUT: Illuminates when the main output is active.
• Nîşana AT: Illuminates when the auto-tuning function is active.
• Nîşaneyên AL1/AL2: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Fonksiyon Bişkojk

• Bişkoka SET: Ji bo ketina moda mîhengkirina parametreyan û piştrastkirina hilbijartinan tê bikar anîn.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. Di moda xebitandina normal de, bikirtînin DANÎN carekê bişkojkê bikirtînin. Dîmendera SV dê dest bi çirûskê bike.
2. Bi kar tînin ▲ (Her) û ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. Bitikîne DANÎN button again to confirm the new SV and exit the setting mode.

6.4 Advanced Parameter Settings

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the DANÎN button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Her) û ▼ (Down) buttons to navigate through parameters and the DANÎN button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Maintenance

• Paqijî: Dîmenderê paqij bike û casinbi qumaşek nerm û hişk bişon. Paqijker an çareserkerên aşınker bikar neynin.
• Berçavderbasî: Periodically check wiring connections for looseness or corrosion.
• Embarkirinî: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

8. Destpêkirin

9. Specifications

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Garantî û Piştgirî

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webmalpera ji bo agahdariya têkiliyê.